Sample and prototype
Confirm the exact actuator, terminal, circuit and validation objective. Engineering reviews sample availability, quantity and freight.
Unionwell engineering support
Micro switch selection guide & specification comparison
Select a micro switch by mechanism, electrical load, environment, operating force and travel. Compare published Unionwell configurations and open technical PDFs.
Review five conditions before comparing models.
- Mechanism: identify the actuator direction, mounting datum, free position, operating point, overtravel and assembly tolerances.
- Circuit: specify voltage, current, inrush, contact arrangement and sensing or power-switching duty.
- Environment: review temperature, liquids, dust, mounting and the cable or connector sealing boundary.
- Evidence: compare the exact drawing revision and relevant product approval, then define an assembly validation plan.
- Supply: state sample or order quantity, annual forecast, project stage and required timing.
Engineering self-selection
Searchable specifications.
Visible configuration scope.
Read published values as text, compare units and open available technical PDFs without leaving contact details. Values apply to the stated example or family configuration, not every option.
G303 — IP67 Waterproof & Dustproof Subminiature Micro Switch G303
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G303 Series |
| Max Operating Force (at pin plunger) | 130gf |
| Terminal Type | Mold Lead Wires/Solder/PCB/Fork Shape |
| Lever Type | No Lever/Hinge/Leaf/Simulated Roller/Roller/Special Design |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating | 0.1A, 125/250VAC; 3A/ 12VDC; 0.1A/48VDC; μ1E5 |
| Operating Frequency / Electrical | 0.1A-120cycles/minute; 3A-10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 Cycles/minute |
| Contact Resistance(Initiative) | 100mΩ Max (without wire type) |
| Vibration Durability | 10~55Hz, move 0.75mm(p-p) |
| Dielectric strength | 500 VAC (50-60 Hz) |
| Operating Temperature | -40 to +85 °C |
| Operating Humidity | 85%RHMax |
| Life Expectancy / Electrical | Min. 100,000 cycles(Depend on model NO.) |
| Life Expectancy / Mechanical | Min. 500, 000 cycles |
G303R — G303R resistor-feedback configuration
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
An inconsistent insulation-resistance unit in a source entry is excluded. Use the current controlled datasheet for that value.
| Parameter | Published value and configuration |
|---|---|
| Published electrical example | 10 mA at 12 VDC - Confirm the sensing circuit and resistor code; this is not a load-switching rating. |
| Operating force at pin plunger | 130 gf / 200 gf options - Actuator geometry changes the force at the mechanism. |
| Circuit options | SPST-NO / SPST-NC - Confirm the required released and actuated states. |
| Protection reference | IEC IP67 - Confirm wire exit, bracket, and assembly sealing. |
| Operating temperature reference | -40 to +85 °C - Validate the complete mechanism and harness at temperature. |
| Model Number | G303R |
| Terminal Type | Lead Wires/Bracket |
| Lever Type | No Lever/Others |
| Contact Resistance / at FP | 150Ω/1000Ω Could be customized |
| Contact Resistance / at OP | 480Ω/1000Ω/2000Ω Could be customized |
| Rating and Electrical Service Life | 10mA 12VDC μ40T85 1E5 |
G303A — Mini Waterproof Micro Switch G303A/B
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G303A/B Series |
| Max Operating Force (at pin plunger) | 180gf/130gf |
| Terminal Type | Mold Lead Wires/Solder/PCB |
| Lever Type | No Lever/Hinge/Leaf |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating | 0.1A, 125/250VAC; 3A/ 12VDC; 0.1A/48VDC; μ1E5 |
| Operating Frequency / Electrical | 0.1A-120cycles/minute; 3A-10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 Cycles/minute |
| Contact Resistance(Initiative) | 100mΩ Max |
| Vibration Durability | 10~55Hz, move 0.75mm (p-p) |
| Dielectric strength | 500VAC (50"60Hz) |
| Operating Temperature | -40° C"+85° C |
| Operating Humidity | 85%RHMax |
| Life Expectancy / Electrical | Min. 100,000 cycles |
| Life Expectancy / Mechanical | Min. 500, 000 cycles |
G303B — Subminiature Micro Switch With Big Solder Terminals G303B
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating | 0.1A, 125/250VAC; 3A/12VDC; 0.1A/48VDC; μ1E5 |
| Operating Frequency / Electrical | 0.1-120 cycles/minute; 3-10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance (Initiative) | 100mΩ Max (without wire type) |
| Vibration Durability | 10~55Hz, move 0.75mm(p-p) |
| Dielectric Strength | 500VAC (50~60Hz) |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 85% RH Max |
| Service Life / Electrical | Min. 100,000/cycles(Depend on part No.) |
| Service Life / Mechanical | Min. 500,000/cycles |
G304 — Subminiature Micro Switch PCB Terminals 150GF G304
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating | 0.1A 125VDC; 50μA 5VDC; 20μA 12VDC: 20mA 12VDC |
| Operating Frequency / Electrical | 20 cycles/minute |
| Operating Frequency / Mechanical | 20 cycles/minute |
| Contact Resistance (Initiative) | 500mΩ Max |
| Vibration Durability | 10-55HZ, move 1.5mm(p-p) |
| Dielectric Strength | 500VAC(50~60HZ) |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 85% RH Max |
| Service Life / Electrical | Min. 300,000/cycles |
| Service Life / Mechanical | Min. 300,000/cycles |
G304A — Mini Waterproof Micro Switch G304A
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G304A |
| Max Operating Force (at pin plunger) | 150gf/Others |
| Terminal Type | Solder/PCB |
| Lever Type | No Lever/Straight Leaf Lever |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120 cycles/min |
| Insulation Resistance | ≥100MΩ |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤500mΩ (Standard Wire Length 300mm) |
| Voltage Resistance / between terminals | AC600V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1500V, 50/60Hz, 1min. |
| Vibration Durability | 10-55Hz 1.5mm(double amplitude) |
| Service Life / Electrical | 300,000 cycles(20 cycles/minute) DC12V 0.1A 50μA 3VDC |
| Service Life / Mechanical | 300,000 cycles(30 cycles/min) |
| Operating Temperature | -40~+85°C |
| Operating Humidity | 85%RH Max |
G304B — Mini Waterproof Micro Switch G304B
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G304B |
| Max Operating Force (at pin plunger) | 150gf/Others |
| Terminal Type | Straight PCB/Others |
| Lever Type | No Lever/Leaf Lever/Straight Leaf Lever/Simulated Roller |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120cycles/min |
| Insulation Resistance | ≥100MΩ |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤200mΩ |
| Voltage Resistance / between terminals | AC600V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1500V, 50/60Hz, Imin. |
| Service Life / Electrical | 300000cycles(20cycles/min)0.1A12VDC; 50μA 5VDC |
| Service Life / Mechanical | 300,000cycles(30cycles/min) |
| Operating Temperature | -40~+85°C |
| Operating Humidity | 85%RHMax |
G304D — Mini Waterproof Micro Switch G304D
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G304D Series |
| Max Operating Force (at pin plunger) | 150gf |
| Terminal Type | Solder/Straight PCB/Left angle PCB/Right angle PCB |
| Lever Type | No Lever/Simulated Roller |
| Circuit Code | SPST-NO/SPST-NC |
| Operating Linear Speed | 30~500mm/s |
| Operating Frequency | 120 cycles/min |
| Insulation Resistance | ≥100MΩ(DC 500V by insulating-resistance meter) |
| Contact Resistance (Initial Value) / with terminals | ≤500mΩ |
| Contact Resistance (Initial Value) / with wires | ≤800mΩ(Wire length 300mm) |
| Voltage Resistance / between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1500V, 50/60Hz, 1min. |
| Service Life / Electrical | 300,000 cycles (30 cycles/min) DC12V 0.1A 50μA 5VDC |
| Service Life / Mechanical | 300,000 cycles (60 cycles/min) |
| Protection Level | IEC IP67 (Except for terminals) |
| Operating Temperature | -40~+85°C |
| Operating Humidity | 95%RH Max(+5~+35°C) |
G304E — Wire Type Subminiature Micro Switch G304E
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Operation Speed | 1~500mm/s |
| Operation Frequency | 120 cycles/min. |
| Insulation Resistance | ≥100MΩ |
| Contact Resistance(Initial Value) / With terminals type | ≤100mΩ |
| Contact Resistance(Initial Value) / With wire type | ≤500mΩ (Standard wire length 300mm) |
| Voltage Resistance / Between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / Between each terminal andthe non-electrical metal parts | AC1,000V, 50/60Hz, 1min. |
| Operating Life / Electrical | 300,000 cycles (15 cycles/min.)DC12V 0.1A 5VDC 50μA |
| Operating Life / Mechanical | 300,000 cycles (30 cycles/min.) |
| Operating Temperature | -40°C~+85°C 60%RH (No icing, no condensation) |
| Operating Humidity | 95%RH (+5°C~+35°C) |
| Vibration / Malfunction | 10-55Hz (Double amplitude 1.5mm) |
G304F — Mini Waterproof Micro Switch G304F
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G304F |
| Max Operating Force (at pin plunger) | 80gf/150gf |
| Terminal Type | Solder/PCB |
| Lever Type | No Lever/V Shape Leaf Lever/Straight Leaf Lever |
| Circuit Code | SPDT/SPST/SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120 cycles /min |
| Insulation Resistance | ≥100MΩ (DC 500V) |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤500mΩ ( length 300mm) |
| Voltage Resistance / between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1000V, 50/60Hz, 1min. |
| Vibration Durability | 10-55Hz |
| Service Life / Electrical | 300000 cycles (20cycles /min) DC12V 0. 1A DC3V 50 μΑ |
| Service Life / Mechanical | 300, 000 cycles (30cycles /min) |
| Protection Level | IEC IP67 |
| Operating Temperature | -40~+85°C 60%RH |
| Operating Humidity | 95%RH (+5~+35°C) |
G304G — Mini Waterproof Micro Switch G304G
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G304G |
| Max Operating Force (at pin plunger) | 80gf/150gf |
| Terminal Type | Solder/Others |
| Lever Type | V Shape Leaf Lever/Straight Leaf Lever/Micro Switch Without Lever |
| Circuit Code | SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120cycles/min |
| Insulation Resistance | ≥100MΩ(DC 500V) |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤500mΩ(300mm) |
| Dielectric Strength / between terminals | AC500V, 50/60Hz, 1min. |
| Dielectric Strength / between terminals and unelectrified metal parts | AC1000V, 50/60Hz, 1min. |
| Vibration Durability | 10-55Hz |
| Service Life / Electrical | 300000 cycles(20 cycles/min) DC12V 0.1A DC3V 50μA |
| Service Life / Mechanical | 300,000 cycles (30cycles/min) |
| Protection Level | IEC IP67 |
| Operating Temperature | -40~+85°C 60%RH |
| Operating Humidity | 95%RH(+5~+35°°C) |
G305 — Mini Waterproof 24 Volt Micro Switch G305
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
Published endurance entries differ between available references; no unified electrical-life claim is made here. Request the current configuration-specific endurance specification.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G305 |
| Max Operating Force (at pin plunger) | 130gf |
| Terminal Type | Mold Lead Wires on Right Side |
| Lever Type | No Lever/#13 Special Lever |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating | 2A 24VDC; 4A 12VDC μ 40T85 10E4 |
| Operating Frequency / Electrical | 0.1A 120cycles/min; 4A 10~30 cycles/min |
| Operating Frequency / Mechanical | 120 cycles/min |
| Contact Resistance (Initial Value) | ≤100mΩ |
| Insulation Resistance | ≥100MΩ |
| Vibration Durability | 10~55Hz, move 0.75mm (p-p) |
| Dielectric Strength | 500VAC (50~60Hz) |
| Operating Temperature | -40~+85°C |
| Operating Humidity | 85%RHMax |
G306 — Mini Waterproof Micro Switch G306
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G306 |
| Max Operating Force (at pin plunger) | 150gf/Others |
| Terminal Type | Wires/Solder/PCB/Others |
| Lever Type | No Lever/Leaf Lever/Hinge Lever/Simulated Roller |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120cycles/min |
| Insulation Resistance | ≥100MΩ |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤500mΩ (wire length 300mm) |
| Voltage Resistance / between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1000V, 50/60Hz, Imin. |
| Vibration Durability | 10-55Hz Double amplitude 1.5mm |
| Service Life / Electrical | 300,000cycles(20 cycles/min)0.1A 30VDC; 10mA 14VDC |
| Service Life / Mechanical | 300,000cycles(30 cycles/min) |
| Protection Level | IEC IP67 (Except for the terminals) |
| Operating Temperature | -40~+85°C 60% RH (without icing or compensation) |
| Operating Humidity | 95%RHMax (under +5°C~+35°C) |
G307 — Mini Waterproof Micro Switch G307
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G307 |
| Max Operating Force (at pin plunger) | 150gf/Others |
| Terminal Type | PCB/Surface Mounted Terminals |
| Lever Type | No Lever/#1 Lever |
| Circuit Code | DPDT/DPST-NO/DPST-NC |
| Operating Linear Speed | 1~500mm/s (depending on the actuating method) |
| Operating Frequency | 120cycles/min |
| Insulation Resistance | ≥100MΩ (500VDC Insulation Resistance Meter) |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Voltage Resistance / between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1000V, 50/60Hz, Imin. |
| Vibration Durability | 10-55Hz Double amplitude 1.5mm |
| Service Life / Electrical | 300,000cycles(20 cycles/min)0.1A 12VDC; 50μA 5VDC |
| Service Life / Mechanical | 300,000cycles(30 cycles/min) |
| Protection Level | IEC IP67 (Except for the terminals) |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 85%RH Max |
G307A — Compact DPDT Momentary Micro Switch Pin Plunger G307A
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating / G307A | 50mA 18VDC 50μA 5VDC |
| Operating Frequency / Electrical | 15~20 Cycles/Min 1~100mm/s |
| Operating Frequency / Mechanical | 15~20 Cycles/Min |
| Initial Contact Resistance | 75mΩ Max. |
| Dielectric Strength | Between Terminals: AC100VBetween Terminal and Housing: AC100V |
| Operating Temperature | -40°C ~+85°C |
| Service Life / Electrical | 300,000 Cycles |
| Service Life / Mechanical | 500,000 Cycles |
G307B — G307B Triple Circuit Loop Momentary Micro Switch
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Operating Frequency | 120 cycles/min |
| Insulation Resistance | ≥100MΩ (DC500V Insulation resistance meter) |
| Contact Resistance (Initial Value) / With terminals type | ≤ 75mΩ |
| Voltage Resistance / Between terminals | AC500V. 50/60Hz, 1min |
| Voltage Resistance / Between terminals and uncharged metal parts | AC500V, 50/60Hz, 1min. |
| Vibration Resistance / No transformation action | 10-55Hz Double amplitude 1.5mm |
| Service Life / Electrical | 150,000 cycles (20 cycles/min) 50mA 18VDC 50μA 5VDC |
| Service Life / Mechanical | 150.000 cycles (30 cycles/min) |
| Protection Level | IEC IP67 (exclude terminals) |
| Operating Temperature | -40°C~+85°C 60%RH (No ice. no frost) |
| Operating Humidity | 95%RH (+5~+35°C) |
G309 — Mini Waterproof Micro Switch G309
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G309 |
| Max Operating Force (at pin plunger) | 80gf/150gf |
| Terminal Type | Solder/PCB |
| Lever Type | No Lever/Others |
| Circuit Code | SPST-NO/SPST-NC |
| Operating Linear Speed | 1~500mm/s |
| Operating Frequency | 120 cycles/min |
| Insulation Resistance | ≥100MΩ(DC 500V by insulating-resistance meter) |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Contact Resistance (Initial Value) / with wires | ≤500mΩ(Wire length 300mm) |
| Voltage Resistance / between terminals | AC500V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1000V, 50/60Hz, 1min. |
| Vibration Durability | 10~55Hz, move 1.50mm(p-p) |
| Service Life / Electrical | 300,000 cycles (20 cycles/min) DC12V 0.1A 50μA 3VDC |
| Service Life / Mechanical | 300,000 cycles (30 cycles/min) |
| Protection Level | IEC IP67 (Except for terminals) |
| Operating Temperature | -40~+85°C |
| Operating Humidity | 95%RH Max(+5~+35°C) |
G5 — G5S05-D1P025-80AU pin-plunger example
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
Rows labelled G5 family reference describe other published family configurations; they are not guaranteed values for the named pin-plunger example.
| Parameter | Published value and configuration |
|---|---|
| Example configuration | G5S05-D1P025-80AU - The example is one configuration, not every G5 or G5E variant. |
| Published ENEC/CQC rating entries | 0.1 A 48 VDC; 0.1 A 125/250 VAC; 5(2.5) A 125/250 VAC - Check the exact temperature grade and approval file for the selected load. |
| Published UL/cUL rating entry | 5 A 1/10 HP 125/250 VAC - Motor and resistive loads require different approval checks. |
| Circuit in this example | SPST-NO - Confirm contact arrangement against the controlled drawing. |
| Actuation in this example | Pin plunger / no lever - Send operating point, overtravel and mounting tolerances. |
| G5 family reference / Operating Frequency | Mechanical 60 cycles/min; Electrical 15 cycles/min. |
| G5 family reference / Insulation Resistance | ≥100MΩ(500VDC) |
| G5 family reference / Contact Resistance (Initial Value) | ≤100mΩ |
| G5 family reference / VoltageResistance / Between each terminals of the same polarity | AC1000V,50/60Hz,1min. |
| G5 family reference / VoltageResistance / Between current-carrying metal part and ground and between each terminal and non-current carrying metal parts | AC1500V,50/60Hz,1min. |
| G5 family reference / Vibration Resistance | 10-55Hz Double amplitude 1.5mm |
| G5 family reference / Service Life | Mechanical ≥10,000,000 cycles or 1,000,000 cycles Electrical ≥50,000 cycles or 100,000 cycles |
| G5 family reference / Unit Net Weight | Approx.6.2g(without lever) |
Additional family reference used in this table ↗
G5E — Basic Micro Switch G5E
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G5E |
| Max Operating Force (at pin plunger) | 100gf/150gf/Others |
| Operating Temperature | -40°C~+85°C |
| Terminal Type | Screw |
| Lever Type | No Lever |
| Circuit Code | SPST-NO |
| Operating Linear Speed | 0.1~1m/s (up to the actuating method) |
| Operating Frequency | Mechanical: 60 cycles/min; Electrical: 15 cycles/min |
| Insulation Resistance | ≥100MΩ(500 VDC) |
| Contact Resistance (Initial Value) | ≤100mΩ |
| Voltage Resistance / between terminals | AC1000V, 50/60Hz, 1min. |
| Voltage Resistance / Between electrified metal parts and housing, and between terminals and unelectrified metal parts | AC1500V, 50/60Hz, 1min. |
| Vibration Durability | 10-55Hz 1.5mm |
| Operating Humidity | 85% RH Max |
| Service Life / Mechanical | 1,000,000 cycles |
| Service Life / Electrical | 50,000 cycles |
G5L — T85 Micro Switch Applicated In Appliances G5L
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G5S05-C2Z015A199-H1U |
| Temperature Grade | 25T85 (For "05" Rating Only) |
| Electrical Rating | ENEC/CQC0.1A 48VDC, 0.1A 125/250VAC, 5(2.5)A 125/250VACUL/cUL0.1A 48VDC, 0.1A 125/250VAC, 5A 1/10HP 125/250VAC |
| Terminal Style | 6.3*0.8mm Quick Connect |
| Circuit Code | SPDT |
| Operating Force at Pin Plunger Max | 15gf |
| Lever Position | Far From Pin Plunger |
G5W11 — G5W11 W3 rating-code reference
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Published W3 ENEC rating entries | 10(2) A 125/250 VAC; 0.5 A 125 VDC; 0.25 A 250 VDC - Other W1/W2 configurations have different ratings. |
| Protection with terminal type | IEC IP67, terminals not included - Protect exposed terminals within the equipment design. |
| Protection with wire type | IEC IP67 - Confirm wire entry and end termination in the final assembly. |
| Initial contact resistance | 50 mΩ maximum with terminals; 100 mΩ maximum with wire - Wire length affects the wired measurement. |
| Storage temperature reference | -40 to +85 °C - Storage temperature is not an operating-temperature approval. |
| Rating / W1 | ENEC: 0.1A 48VDC, 0.1A 125/250VAC,40T85,5E4,uUL:0.1A 48VDC,0.1A 125/250VAC,T85 |
| Rating / W2 | ENEC: 5A 125/250VAC,5A, 30VDC,40T85,5E4, uUL:5A 125/250VAC,T85 |
| Rating / W3 | ENEC:10(2)A 125/250VAC, 0.5A 125VDC, 0.25A 250VDC,40T85,u,2E4UL:10.1A 1/10HP 125/250VAC,0.5A 125VDC, 0.25A 250VDC, T85 |
| Operating Frequency / Electrical | 10~30 times/min |
| Operating Frequency / Mechanical | 60 times/min |
| Insulation Resistance | at 500VDC,100MΩ Min. |
| Dielectric Strength / Between Terminals | AC 1000V 50-60Hz 1min |
| Dielectric Strength / Between Terminals And Housing | AC 1500V 50-60Hz 1min |
| Storage Humidity | 85%RH Max |
| Life / E-life | 2E4~10E4 cycles(depends on P/Ns) |
| Life / M-life | over 1,000,000 cycles(60 cycles/min) |
| Weight | Approx.7g(with terminal and without lever) |
G6 — Mini Micro Switch G6
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
An inconsistent insulation-resistance unit in a source entry is excluded. Use the current controlled datasheet for that value.
Original company G6 catalogue drawings and ordering references follow the text summary in the PDF. The S00AU travel example does not describe lever variants.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G6 Series |
| Operation Force | 50gf/100gf/150gf/250gf/350gf |
| Terminal Type | Solder/PCB/Quick Connect |
| Lever Type | No Lever/Hinge/Simulated Roller/Roller |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating / P1/P11/P12 | ENEC: 0.1A,125/250V 48VDC 5EA UL: 0.1A,125/250V 48VDC Gold Plated Contact Optional |
| Rating / 05/051/052 | ENEC: 5A,125/250VAC UL: 5A, 1/8HP 125/250VAC |
| Rating / 10/101 | ENEC: 10(2)A,125/250VAC μ 25T125 UL: 10.1A, 1/4HP 125/250VAC Note: Only with ''OF''over ''250gf'' |
| Rating / 12 | ENEC: 12(6) A,125/250VAC μ 40T125 UL: 12A, 125/250VAC Note: Only with 350gf OF |
| Operating Frequency / Electrical | 10-30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance(Initiative ) | 100mΩ Max (without wire type) |
| Dielectric strength | 1,000 VAC, 50–60 Hz for 1 minute (between terminals) |
| Operating Temperature | -25°C~+125°C |
| Storage Humidity | 85% RH Max |
| Life Expectancy / Electrical | 10,000-50,000 cycles (depending on specific model selection) |
| Life Expectancy / Mechanical | 1,000,000 cycles |
| Insulation resistance — company G6 PDF reference | 100 MΩ minimum at 500 VDC |
| Pre-travel — S00AU pin-plunger drawing example | 1.0 mm maximum |
| Overtravel — S00AU pin-plunger drawing example | 0.4 mm minimum |
| Movement differential — S00AU pin-plunger drawing example | 0.2 mm maximum |
| Free position — S00AU pin-plunger drawing example | 9.1 mm maximum |
| Operating position — S00AU pin-plunger drawing example | 8.5 ± 0.3 mm |
G9 — G9A05-200S00A-U spherical pin-plunger example
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
An inconsistent insulation-resistance unit in a source entry is excluded. Use the current controlled datasheet for that value.
| Parameter | Published value and configuration |
|---|---|
| Example configuration | G9A05-200S00A-U - Confirm whether G9, G9A or G9B matches the mechanism. |
| Published UL/cUL rating entries | 5 A 125/250 VAC; 5 A 30 VDC - Confirm load category and current controlled approval scope. |
| Operating force | 200 gf maximum - This reference is for the pin-plunger example. |
| Terminal in this example | Solder terminals - Specify harness routing and the available termination process. |
| Circuit in this example | SPDT - Check common, normally open and normally closed terminal positions. |
| Model Number | G9A05-200S00A-U |
| Electrical Rating | ENEC/CQC: 5(2)A 125/250VAC 30VDC 40T85 5E4 μUL/CUL:5A 125/250VAC 30VDC |
| Operation Force | 200gf Max |
| Terminal Stle | Solder terminals |
| Lever Type | No lever pin plunger |
G9A — Waterproof Momentary Micro Switch G9A
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating / p1 | 0.1A 125/250VAC,0.1A 30VDC |
| Rating / 05 | 5(2)A 125/250VAC,5A 30VDC |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance(Initiative) / With terminals type | 100mΩ Max |
| Contact Resistance(Initiative) / With wires type | 200mΩ Min |
| Insulation Resistance (at 500VDC) | 100MΩ Min |
| Voltage Resistance / Between terminals | AC 500V, 50/60HZ,1 Min |
| Voltage Resistance / Between terminals and uncharged metal parts | AC 1000V, 50/60HZ,1 Min |
| Service Life / Electrical | 50,000 cycles |
| Service Life / Mechanical | 200,000 cycles(IP67) 2,000,000 cycles(IP40) |
| Storage Temperature | -40°C~+85°C |
| Storage Humidity | 95% RH Max |
G91 — Mini Micro Switch G91
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model | Mini Micro Switch G91 |
| Operation Force | 100gf/150gf/250gf/300gf |
| Terminal Type | Solder/PCB/Quick Connect |
| Lever Type | No Lever/Pin Plunger/Cambered Surface/Straight/Simulated Roller/Roller |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating / P1 | 0.1A,125/250V 48VDC Gold Plated Contact Optional |
| Rating / 05 | ENEC: 5A 125/250VAC; 5A 1/8HP, 125/250VAC |
| Rating / 10 | ENEC: 10(1.5A) 125/250VAC; UL:10A 1/4HP 125/250VAC |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance(Initiative) | 100mΩ Max |
| Dielectric strength | AC, 1,000RMS(50-60Hz) |
| Operating Temperature | -40°C~+125°C or -40°C~+85°C |
| Operating Humidity | 85% RH Max |
| Life Expectancy / Electrical | 10,000-100,000 cycles (depending on specific model selection) |
| Life Expectancy / Mechanical | 500,000 cycles |
G10 — Subminiature Switch PCB Terminals G10
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating / P1 | 0.1A 48VDC/125VAC(Gold Plated Optional) |
| Rating / 03 | 1A/3A 125VAC |
| Operating Frequency / Electrical | 10~30 Cycles/Minute |
| Operating Frequency / Mechanical | 120 Cycles/Minute |
| Contact Resistance(initial value) | 100mΩ Max (Depends On P/Ns) |
| Insulation Resistance | at 500VDC,100MΩ Min. |
| Dielectric Strength | AC 600VAC RMS (50-60HZ) |
| Storage Temperature | -40°C~+85°C |
| Storage Humidity | 85%RH Max |
| Service Life / Electrical | 6,000 ~ 100,000 cycles(Depends On P/Ns) |
| Service Life / Mechanical | 1,000,000 Cycles |
| Unit Net Weight | About 0.5g(Straight PCB Type Without Lever) |
G10A — Small Micro Switch G10A
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G10A Series |
| Max Operating Force (at pin plunger) | 150gf Max |
| Terminal Type | Mold Lead Wires/Solder/PCB |
| Lever Type | No Lever/Hinge/Leaf |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating / P1 | 0.1A-120cycles/minute; 3A-10~30 cycles/minute |
| Rating / 03 | 120 Cycles/minute |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance(Initial Value) | 100mΩ Max (Depends on P/Ns) |
| Insulation Resistance (at 500VDC) | At 500VDC, 100MΩ Min |
| Dielectric strength | AC 600V RMS (50-60HZ) |
| Storage Temperature | "-40°C-+85°C |
| Storage Humidity | 85%RH Max |
| Life Expectancy / Electrical | 10,000 cycles |
| Life Expectancy / Mechanical | 1,000,000 cycles |
G10B — Subminiature Sealed Micro Switch G10B Series
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating / P1 | 0.1A 125/250VAC 30VDC |
| Rating / 03 | 3A 125/250VAC 30VDC |
| Operating Frequency / Electrical | 10~30 cycles/min |
| Operating Frequency / Mechanical | 120 cycles/min |
| Contact Resistance (Initial Value) | 100mΩ Max. |
| Insulation Resistance (at 500VDC) | 100MΩ Min. |
| Dielectric Strength / Between teminals | 600VAC 50~60Hz for 1 Min |
| Dielectric Strength / Between terminals and housing | 1,000VAC 50~60Hz for 1 Min |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 85%RH Max |
| Service Life / Electrical | 10,000 cycles |
| Service Life / Mechanical | 1,000,000 cycles |
G11 — DPDT Sealed Micro Switch G11
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G11 Series |
| Max Operating Force (at pin plunger) | 350/450gf |
| Terminal Type | Mold Lead Wires |
| Lever Type | No Lever/Straight/Roller |
| Circuit Code | DPDT/DPDT-NO/DPDT-NC |
| Rating | 0.5A/5A 250VAC; 0.5A 250VDC |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 Cycles/minute |
| Contact Resistance(Initiative) | 30~100mΩ Max (Depend on P/N, wire resistance exclude) |
| Insulation Resistance (at 500VDC) | 100MΩ Min |
| Dielectric strength | 750VAC (50~60Hz) |
| Operating Temperature | -25~+85°C |
| Operating Humidity | 85%RHMax |
| Service Life / Electrical | 50,000 cycles (Depend on P/N ) |
| Service Life / Mechanical | 2,000,000 cycles |
G12 — Large Limit Switch G12
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G12 Series |
| Operating Force ( at pin plunger ) | 70gf/120gf/100gf/170gf/105gf/140gf/150gf/180gf/230gf/250gf/ 370gf/430gf/620gf |
| Terminal Type | Screw terminals/Solder terminals/other |
| Lever Type | Pin plunger/Spring pin plunger/Panel mounting plunger/Panel mounting roller plunger/Panel mounting cross roller plunger/Swing lever/short swing lever/Roller swing lever/short swing lever/Spring straight lever/Spring roller lever/other |
| Circuit Code | SPDT/SPST-NC/SPST-NO |
| Rating / 16A | ENEC/CQC 16A 125/250 or 480VAC 1/8HP 125VAC 1/4HP 250VAC 0. 5A 125VDC 0. 25A 250VDC |
| Rating / 16A | UL/ cUL 16A 125/250VAC 5E4 µ 40T85 |
| Rating / 22A | ENEC/CQC 22A 125/250 or 480VAC 1/4HP 125VAC 1/2HP 250VAC 0. 5A 125VDC 0. 25A 250VDC |
| Rating / 22A | UL/cUL 22A 125/250VAC 5E4 µ 40T85 |
| Rating / 26A | ENEC/CQC 26A 125/250 or 480VAC 1/4HP 125VAC 1/2HP 250VAC 0. 5A 125VDC 0. 25A 250VDC |
| Rating / 26A | UL/ cUL 26A 125/250VAC 5E4 µ 40T85 |
| Operating Frequency / Electrical | 10~30 cycles/min |
| Operating Frequency / Mechanical | 240 cycles/min |
| Contact Resistance (Initiative Value) | 50mΩ Max |
| Insulation Resistance (at 500VDC) | 100MQ Min (at500VDC) |
| Dielectric strength / Between Terminals | 1500VAC 50/60Hz 1min |
| Between Terminals and Housing | 2500VAC 50/60Hz 1min |
| Storage Temperature | -40° C"+85° C |
| Storage Humidity | 85%RHMax |
| Life Expectancy / Electrical | 50, 000 cycles or 100, 000 cyclesDepends on part No. |
| Life Expectancy / Mechanical | 10, 000, 000 cycles |
| Unit Net Weight | Approx60g (Drip-proof panel mounting type) |
G15D — Miniature Micro Switch Roller Lever G15D
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Series No. / G15DP1 / G15D01 | Customized |
| Operating Force | 15gf 30gf 60gf 110gf |
| Contacts / Silver Alloy | Gold Plated |
| ElectricalRating / O.1A DC30V / 1A DC15V | 0.1A DC30V |
| Contact Resistance(Initial value) | 100mΩ Max |
| Operating Frequency | Mechanical: 60 cycles max Electrical: 20 cycles max |
| Insulation Resistance | 100MΩ(DC 500V) Min |
| Voltage Resistance | AC250V 50/60Hz 1min |
| Mechanical Life / 20,000 cycles / 300,000 cycles / 300,000 cycles | 1,000,000 cycles |
| Electrical Life / 20,000 cycles / 300,000 cycles / 10,000 cycles | 1,000,000 cycles |
| Storage Humidity | 85% RH max at +40°C |
| Operating Temperature Range | -40~+85°C |
| Solder Ability | 255±5°C 5s |
| Protection Type | IP40 |
| Unit Net Weight | Approx 0.3g |
G15E — Ultra-miniature Micro Switches G15E
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Series No. / G15EP1 | G15E01 |
| Operating Force | 60gf Max. |
| Contacts / Silver Alloy | Gold Plated |
| ElectricalRating / O.1A DC30V | 1A DC15V |
| Contact Resistance(Initial value) | 100mΩ Max |
| Operating Frequency | Mechanical: 60 cycles max Electrical: 20 cycles max |
| Insulation Resistance | 100MΩ(DC 500V) Min |
| Voltage Resistance | AC250V 50/60Hz 1min |
| Mechanical Life / 20,000 cycles / 300,000 cycles | 300,000 cycles |
| Electrical Life / 20,000 cycles / 300,000 cycles | 10,000 cycles |
| Storage Humidity | 85%RH max at +40°C |
| Operating Temperature Range | -40~+85°C |
| Solder Ability | 255±5°C 5s |
| Protection Type | IP40 |
| Unit Net Weight | Approx 0.3g |
G16 — Swing Rotary Switch G16
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G16 |
| Rating | 0.1A 12VDC |
| Operating Frequency / Electrical | 20 cycles/min. |
| Operating Frequency / Mechanical | 30 cycles/min. |
| Contact Resistance (Initial Value) | 200mΩ Max. |
| Vibration Durability | 10~55Hz, Amplitude 1.5mm |
| Voltage Resistance / Between Terminals | 500VDC 50-60Hz 1min |
| Voltage Resistance / Between terminals and housing | 1000VAC 50-6OHz 1min |
| Service Life / Electrical | 100,000 cycles |
| Service Life / Mechanical | 100,000 cycles |
| Operating Force | 200gf Max |
| Storage Temperature | -40°C~+85°C |
| Storage Humidity | 85%RH Max |
| Unit weight | 1.6g |
G19 — G19 seat-adjustment family reference
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
An inconsistent insulation-resistance unit in a source entry is excluded. Use the current controlled datasheet for that value.
| Parameter | Published value and configuration |
|---|---|
| Published electrical-life example | 15 A at 14 VDC, 30,000 cycles - Confirm the exact configuration, motor load and test conditions. |
| Published mechanical-life reference | 50,000 cycles - Electrical and mechanical life are different measures. |
| Initial contact resistance | 20 mΩ maximum - Confirm the test method and connection points. |
| Protection reference | IP67, exposed terminals excepted - Review connector and enclosure protection separately. |
| Operating temperature reference | -40 to +85 °C - Confirm the selected actuator and vehicle validation plan. |
| Operating Frequency | 10 cycles/minute |
| Operating Humidity | <95%RH(+5~+35°C) |
| Stick height option A | 22mm |
| Stick height option B | 21.6mm |
| Stick height option C | 25.6mm |
G20 — G20 Seat Belt Reminder Switch
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating | 5 ~ 1000mA 4 ~48VDC (up to different resistance selection) |
| Operating Frequency / Mechanical | 120 cycles/min |
| Operating Frequency / Electrical | 10~30 cycles/min 1~500mm/s |
| Initial Contact Resistance | 100mΩ Max. (single switch, excluding resistors) |
| Insulation Resistance | 100MΩ Max. (single switch, excluding resistors) |
| Dielectric Strength | Between terminals: AC 500V (single switch, excluding resistors)Between terminals and housing: AC 1000V |
| Operating Temperature | -40°C~ +85°C |
| Service Life / Mechanical | 300,000 cycles |
| Service Life / Electrical | 1,000,000 cycles |
G21 — DPDT Micro Switch G21
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G21 |
| Max Operating Force (at pin plunger) | 250gf |
| Terminal Type | Solder/PCB |
| Lever Type | No Lever/Others |
| Circuit Code | SPST-NO/SPST-NC |
| Rating | DC14: 6A 12VDC; 2A 24VDC 0.6A 55VDC |
| Operating Frequency / Electrical | 60 cycles/minute |
| Operating Frequency / Mechanical | 180 cycles/minute |
| Contact Resistance(Initiative) | 100mΩMax |
| Insulation Resistance (at500VDC) | 100MΩ Min |
| Service Life / Electrical | 1000,000 cycles |
| Service Life / Mechanical | 3000,000 cycles |
| Storage Temperature | -30°C 〜+85°C |
| Storage Humidity | 95%RH Max |
| Operating Temperature Range | -30°C 〜+65°C |
G23A — G23A Motor Electronic Lock for DC Charging Gun
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rating | 12VDC. |
| Insulation Resistance(at 500VDC) | 100MΩ Min. |
| Dielectric Strength | 500VAC (50~60Hz) |
| Degree of Protection | IEC IP67(the drive roller and housin excepted) |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 45%RH~85%RH |
| Service Life / Electrical | 60,000 cycles |
| Service Life / Mechanical | 60,000 cycles(Min.) |
| Operating Frequency / Electrical | 20 cycles/minute |
| Operating Frequency / Mechanical | 20 cycles/minute |
| Operating Features (At 12VDC) / OF | 700g.cm(Min.) |
| Operating Features (At 12VDC) / HF | 250g.cm(Min.) |
| Operating Features (At 12VDC) / PT | 45°±5° |
| Operating Features (At 12VDC) / Shaft Strength | 200N(No mechanical damage under vertical axial force) |
| Operating Features (At 12VDC) / Manual Unlocking Torque (OF) | 250g.cm(Min.) |
G23B — G23B Motor Electronic Lock for Onboard AC Charging Socket
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Rated voltage | 12VDC (pulse) |
| Voltage range | 12±10% VDC. |
| Idling current | <50mA |
| Locked-rotor current | <500mA |
| Response time | <100mS |
| Maximum power on time | 3S (No long time conduction) |
| Locking time | <300mS |
| Unlocking time | <300mS |
| Triggering time at 12VDC | 0.25S<t<1S |
| Functional angle | <90° |
| Insulation Resistance | 100MQ Min |
| Dielectric Strength | 500VAC (50~60Hz) |
| Degree of Protection | IECIP54 Except driving wheel and push rod active cavity |
| Operating Temperature | -40°C~+85°C |
| Operating Humidity | 45%RH~85%RH |
| Service Life / Electrical | 30,000 cycles |
| Service Life / Mechanical | 30,000 cycles (Min.) |
| Operating Frequency / Electrical | 18 cycles/min |
| Operating Frequency / Mechanical | 18 cycles/min |
| Operating Features (At 12VDC) / HF | 300g (Min.) |
| Operating Features (At 12VDC) / Fracture Force | 200N |
| Operating Features (At 12VDC) / PT | 8.0mm±0.20mm |
| Operating Features (At 12VDC) / OF | 300g.cm (Min.) |
G25 — G25 Push Button Switch
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Operating Frequency | 15-20 cycles/min |
| Insulation Resistance | ≥3MΩ(VDC 100V Insulation Resistance Meter) |
| Contact Resistance (Initiative) / with terminals type | ≤100mΩ |
| Dielectric Strength / Between terminals | AC100V. 50/60Hz, 1min. |
| Dielectric Strength / Between terminals and uncharged metal parts | AC1500V. 50/60Hz. 1min. |
| Service Life / Electrical | 300,000 cycles (15-20 cycles/min) 50mA 18VDC 50μA 5VDC |
| Service Life / Mechanical | 300,000 cycles (30 cycles/min) |
| Operating Temperature | -40° C- +85° C 60%RH(No ice.no frost) |
| Operating Humidity | 95%RH ( + 5~+35°C) |
GT01 — Detector Micro Switch GT01
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | GT01 |
| ElectricalCharacteristics / Rating | 0.1A 12VC; 50μΑ |
| ElectricalCharacteristics / Contact Resistance | 100 mΩ Max. (Initial Value) |
| ElectricalCharacteristics / Insulation Resistance | 50MΩ Min. |
| ElectricalCharacteristics / Voltage Resistance | 100VAC (50/60Hz) 1Minute |
| ElectricalCharacteristics / Electrical life | 10,000 Cycles (Min) |
| Parameters / Operating Force | See Detailing Spec |
| Parameters / Mechanical Life | 100,000 Cycles (Min) |
| Parameters / Operating Temperature Range | -25°C~+80°C |
| Parameters / Operating Humidity | ≤85%RH |
| Parameters / Solder Ability | 260°C ± 5 °C 3s ± 1s |
GPS100 — Air Pressure Micro Switch GPS100
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | GPS100 |
| Set Point Range | 10-1500Pa |
| On Pressure Range | 25-1500Pa |
| Off Pressure Range | 10Pa Min. |
| Circuit Code | SPST-NO/SPST-NC/SPDT |
| Switch Rating | 0.1A 125/250VAC,3A 125/250VAC,5A 125/250VAC,16A 125/250VAC |
| Switching Element | Snap Action Switch |
| Measured Media | Air |
| Operating Temperature | -40~+90°C |
G1 — Mini Tact Switch G1/G17
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model | G1/G17 |
| Rating | 12VDC 20 Jl A~20mA |
| Operating Frequency / Electrical | 20 cycles/minute |
| Operating Frequency / Mechanical | G1 Series 120 cycles/minute |
| Operating Frequency / Mechanical | G17 Series 80 cycles/minute |
| Contact Resistance(Initial Value) | ＜200mΩ |
| Vibration durability | 10~55Hz,Amplitude 1.5mm |
| Voltage Resistance / Between Terminals | 500 VAC (50~60 Hz) |
| Voltage Resistance / Between Terminals and housing | 1500 VAC (50~60Hz) |
| Service life / Blectrical | 100,000 cycles |
| Service life / Mechanical | 100,000 cycles |
| Sorage Temperature | -40~+85°C |
| Storage Humidity | 85 % RH MAX |
| Unit Weight | G1: 0.85g |
| Unit Weight | Gl7: 1.1g |
G17 — Mini Tact Switch G1/G17
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model | G1/G17 |
| Rating | 12VDC 20 Jl A~20mA |
| Operating Frequency / Electrical | 20 cycles/minute |
| Operating Frequency / Mechanical | G1 Series 120 cycles/minute |
| Operating Frequency / Mechanical | G17 Series 80 cycles/minute |
| Contact Resistance(Initial Value) | ＜200mΩ |
| Vibration durability | 10~55Hz,Amplitude 1.5mm |
| Voltage Resistance / Between Terminals | 500 VAC (50~60 Hz) |
| Voltage Resistance / Between Terminals and housing | 1500 VAC (50~60Hz) |
| Service life / Blectrical | 100,000 cycles |
| Service life / Mechanical | 100,000 cycles |
| Sorage Temperature | -40~+85°C |
| Storage Humidity | 85 % RH MAX |
| Unit Weight | G1: 0.85g |
| Unit Weight | Gl7: 1.1g |
G2 — Rotary Micro Switch G2
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G2 |
| Rating | 0.1A 12VDc |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/minute |
| Contact Resistance (Initial Value) | 100mΩ Max. |
| Vibration Durability | 10~55Hz, move 0.75mm (p-p) |
| Dielectric Strength | 500VAC (50~60Hz) |
| Storage Temperature | -30°C~+85°C |
| Storage Humidity | 85%RH MAX. |
| Service Life / Electrical | 100,o00 cycles |
| Service Life / Mechanical | 100,000 cycles Min. |
G606 — DPDT Micro Switch G606
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G606 Series |
| Max Operating Force (at pin plunger) | 200gf |
| Terminal Type | Long Solder/Straight PCB/Left angle PCB/Right angle PCB/Side Solder |
| Lever Type | No Lever/Straight/Straight Lever With Hole |
| Circuit Code | DPDT-NO/DPDT |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 cycles/min |
| Insulation Resistance | ≥100MΩ(at 500VDC) |
| Contact Resistance (Initial Value) | 30~100mΩMax ( Depend on P/N) |
| Dielectric strength | AC750V RMS, 50~60Hz |
| Service Life / Electrical | 50,000~100,000 cycles (Depend on P/N) |
| Service Life / Mechanical | 500,000 cycles |
| Operating Temperature | -40~+125°C |
| Operating Humidity | 85%RH Max |
SWP — Door Micro Switch SWP
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | SWP Series |
| Max Operating Force (at pin plunger) | 200gf/Others |
| Terminal Type | Solder |
| Lever Type | No Lever |
| Circuit Code | Single Pole |
| Rating | 0.25A, 250VAC; 0.5A 24VDC |
| Operating Frequency / Electrical | 10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 Cycles/minute |
| Tracking Resistance | PTI 250°C |
| Glow Wire | 850°C |
| Contact Resistance(Initiative) | 100mΩ Max |
| Operating Temperature | -20° C"+60° C |
| Operating Humidity | 10%~85%RHMax |
| Life Expectancy / Electrical | 100,000 cycles |
| Life Expectancy / Mechanical | 200,000 cycles |
SWD — Sealed Explosion Proof Fridge Door Micro Switch SWD
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | SWD01A/ SWD06A |
| Max Operating Force (at pin plunger) | 150gf/Others |
| Terminal Type | Wires/Solder/PCB/Others |
| Lever Type | No Lever/Leaf Lever/Hinge Lever/Simulated Roller |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Operating Linear Speed | 7.5~500mm/s |
| Operating Frequency / Mechanical | 60 cycles/min |
| Operating Frequency / Electrical | 20 cycles/min |
| Insulation Resistance | ≥100MΩ (500VDC Insulation Resistance Meter) |
| Contact Resistance (Initial Value) / with terminals | ≤100mΩ |
| Voltage Resistance / between terminals | AC1000V, 50/60Hz, 1min. |
| Voltage Resistance / between terminals and unelectrified metal parts | AC1500V, 50/60Hz, 1min. |
| Vibration Durability | 10-55Hz Double amplitude 1.5mm |
| Service Life / Electrical | 2.5A 125/250VAC 25T85 μ 5E46A 125/250VAC 25T85 μ 1E40.1A 125/250VAC 0.1A 30VDC 25T85 μ 5E4 |
| Service Life / Mechanical | 300,000 cycles(60 cycles/min) |
| ATEX Proof and Certificate Number | S 20 ATEX 107202 0001U3 G EX nC II C Gc |
| PTI | 450V |
| Operating Temperature | -25~+85°C |
| Operating Humidity | 95% RH Max |
G3 — G303 published example within the G3 platform
Published reference values describe the stated series or example configuration. Confirm the complete part number, load, actuator drawing and current approval scope before design release.
| Parameter | Published value and configuration |
|---|---|
| Model Number | G303 Series |
| Max Operating Force (at pin plunger) | 130gf |
| Terminal Type | Mold Lead Wires/Solder/PCB/Fork Shape |
| Lever Type | No Lever/Hinge/Leaf/Simulated Roller/Roller/Special Design |
| Circuit Code | SPDT/SPST-NO/SPST-NC |
| Rating | 0.1A, 125/250VAC; 3A/ 12VDC; 0.1A/48VDC; μ1E5 |
| Operating Frequency / Electrical | 0.1A-120cycles/minute; 3A-10~30 cycles/minute |
| Operating Frequency / Mechanical | 120 Cycles/minute |
| Contact Resistance(Initiative) | 100mΩ Max (without wire type) |
| Vibration Durability | 10~55Hz, move 0.75mm(p-p) |
| Dielectric strength | 500 VAC (50-60 Hz) |
| Operating Temperature | -40 to +85 °C |
| Operating Humidity | 85%RHMax |
| Life Expectancy / Electrical | Min. 100,000 cycles(Depend on model NO.) |
| Life Expectancy / Mechanical | Min. 500, 000 cycles |
Complete the mechanical selection
Actuator-specific operating point, pre-travel, overtravel, release point, mounting datum and dimensional tolerances must be checked against the complete part number's drawing. A nominal family size or IP reference does not confirm fit inside your assembly.
From selection to quotation
Quote the configuration
and the quantity together.
Pilot production
Review drawing release, approval scope, tooling, packing and trial requirements before confirming the pilot quantity and timing.
Repeat production
Share the order quantity and annual forecast. Quantity breaks, capacity and delivery are quoted for the released part number.
Pricing and availability are confirmed after review. No unverified stock count, universal MOQ or fixed lead time is displayed.
Plan the next sourcing step.
Can a resistor-feedback switch be replaced by a plain contact?
Do not assume equivalence. The sensing circuit may distinguish normal and fault states using resistance. Share the circuit, resistor values, diagnostic thresholds, and complete part number.
What determines the MOQ for this configuration?
The quotation depends on the exact actuator, terminal or wire assembly, contact material, special tooling, packing, and annual forecast. Send the complete part number and sample or production quantity to confirm the applicable MOQ.
How are sample and production lead times confirmed?
Lead time is quoted after the drawing, configuration, validation needs and quantity are reviewed. Samples, custom tooling and repeat production follow different schedules. No unconfirmed stock or fixed delivery time is assumed.
Can I download a drawing or approval for every variant?
The catalogue and published reference record can be viewed here. Request the current 2D/3D file, drawing revision and product approval for your complete part number. Management-system certificates describe the manufacturing organization, not an approval for every switch variant.
Make the next engineering decision